Guns International #: 102814821
Seller's Inventory #: CCM/M-16 U
Click Photo to Enlarge |
Guns International #: 102814821
Category - AR15 Complete Uppers
- Gun Parts - AR-15 Upper
Canadian Colt m-16 Upper Assembly
Description: SCARCE COLT U.S. CANADIAN MILITARY CONTRACT COMPLETE M-16 UPPER ASSEMBLY W/ ORIGINAL TROY/ VIKING TACTICS 11 1/8 INCH FREE FLOATING HANDGUARD ASSEMBLY’’ & COLT FLAT TOP RECEIVER W/ /FULL LENGTH PICATINNY RAIL (GRADUATED FROM T1 to T42)! NOTE: THIS IS A 100% & TOTALLY COMPLETE COLT MILITARY M-16 UPPER (Less only the Removable Flip Up/Sights). This is an actual 100% original complete Canadian Colt M-16 military assembly, exactly as taken off o a Canadian Colt M-16 military rifle. Condition - used very good+ No FFL required. SEE MORE BELOW: Cal. 5.56 NAT, barrel length 14 3/4 Inches. See Following Important ATF Legal Information Below. This is indeed the ‘’real thing’’ and a totally 100% COMPLETE M-16 Upper Assembly! This 100% Original and totally complete Military M-16 Upper assembly is as stated of Colt Manufacture for the Canadian Military and exactly as taken right off a Military Canadian M-16 Carbine! The receiver is totally complete with its original and perfect flip open dust door assembly and complete excellent Colt bolt assist assembly and the carrier is correctly "C" marked on its left side, with the bolt assembly correctly contract "D" marked. The firing pin is the latest chrome plated variation. Other than simply expected cycling wear mostly on the carrier’s bottom the original visible finish rates the same approx 98%. The original Charging Handle simply shows only expected cycling/operational wear. *The Barrel Assembly is of the ‘’FreeFloating’’ type being also of Colt manufacture and perfectly Colt marked with ‘‘C MP over 5.56 NATO 1/7’’ and the original Colt exterior finish rates the same appx. 98% and visually with only a patch ran through the Bore it rates appx. VG+/near Excellent! The barrel is surrounded by the The Factory Original Free Floating ‘’TROY/VIKING TACTICS’’ Forearm that is a full 11 1/8 inches in length and graduated on its Picatinny rail from T16 to T42 being fully consistent to the above mentioned receiver with both graduated continuously from T1 to T42! *FYI: Again, as Factory assembled this is a FULL CONTINUOUS ‘’T1 to T42 GRADUATED PICTINNY SIGHT RAIL! (*This Picatinny Rail is manufactured for the Military to accept any sight systempreferred (even telescopic sights) therefore no sights are included). This assembly shows only very light service/use on its hand guard sides and other than that rates appx. the same 98% original finish is perfectly marked: right rear side with ‘’TROY (LOGO) VIKING’’ and on the upper between the graduated lugs perfectly marked ‘’TROY, TX EXREME/BATTLERAIL, TROYIND.COV, PATENT/PENDING, P/N TRXE 110/LOT RD-5240’’. NOTE: Again, the barrel is currently of 14 3/4 inches with NO Flash Hider and with the current Factory flash hider on it measures appx 15 3/4’’ which is still a bit shy of the legal length. To conform to legal length, it will need just a bit longer Flash Hider which can easily be obtained, screwed on and then pinned and welded. This is a very simple procedure done by any gun smith. Ownership of the above assembly ‘’as it is’’ without its lengthening is NOT Illegal as long as it is not assembled on to a lower receiver. If it is to be assembled on to a lower receiver it must be lengthened as mentioned above. NOTE: As with everything we offer please check with your local jurisdictions. BUYERS RESPONSIBILITY TO RESEARCH LOCAL LAWS! This is rarely found, TOTALLY COMPLETE CANADIAN M-16 UPPER ASSEMBLY and not the FFL required SN’d Lower, so No FFL is required to purchase. Price: $650.00 Contact Seller |
Guns International #: 102814821
Seller's Inventory #: CCM/M-16 U
Guns International #: 102814821
Seller's Inventory #: CCM/M-16 U